How to Reline a Troy Bilt Weed Eater? Troy-Bilt Bump Head

Introduction

Troy-Bilt is one of the most trusted names in outdoor power equipment, and its weed eaters are a top choice for both homeowners and professional landscapers thanks to their durability and consistent performance. Like all string trimmers, however, the cutting line on a Troy-Bilt weed eater wears down over time from friction with grass, weeds, rocks, and dirt. If you’ve ever been mid-trim only to have your line snap or stop advancing, you know how disruptive a malfunctioning trimmer can be. The good news is that learning how to reline a Troy Bilt weed eater is a simple, low-cost skill that will save you hundreds of dollars in professional repair bills over the life of your equipment. Most users can complete a full reline in 10 to 15 minutes with just a few basic tools, no special training required. This comprehensive guide covers everything you need to know, from identifying when you need a new line to step-by-step instructions for relining Troy-Bilt bump heads, key differences between feed systems, tips to extend line life, and common mistakes to avoid. Whether you’re a first-time Troy-Bilt owner or a seasoned user looking to refresh your maintenance routine, this guide has you covered.

• Introduction
• Understanding Your Troy-Bilt Weed Eater Line
• Types of Troy-Bilt Weed Eater Line
• Signs You Need to Reline Your Troy-Bilt Weed Eater
• Tools and Materials You’ll Need for Relining
• Step-by-Step Guide: How to Reline a Troy Bilt Weed Eater?
• Troy-Bilt Bump Head vs. Autofeed Head: Key Differences
• Tips for Extending Your Weed Eater Line Life
• Common Mistakes to Avoid When Relining
• Frequently Asked Questions
• Conclusion

Understanding Your Troy-Bilt Weed Eater Line

The cutting line is the core working component of your Troy-Bilt weed eater, responsible for slicing through grass, weeds, and light brush. Using the right type and size of line for your specific model is critical for optimal performance, and it will also prevent unnecessary strain on your trimmer’s engine and cutting head. Using an incompatible line can lead to frequent breakage, poor cutting results, and even permanent damage to your equipment over time. Before you purchase replacement line, take a few minutes to review your owner’s manual or check the label on your existing line spool to confirm the correct specifications for your model.

Types of Troy-Bilt Weed Eater Line

Troy-Bilt weed eaters are compatible with several types of cutting line, each designed for different use cases and cutting conditions:

• Round line: The most common and affordable option, round line has a smooth, circular cross-section. It works well for general residential use, cutting soft grass and thin weeds, but it dulls quickly when used on thick, woody vegetation.
• Square line: With four sharp edges, square line cuts more efficiently than round line and holds its edge longer. It’s ideal for thicker weeds, overgrown grass, and light brush, making it a popular choice for users with larger yards or more demanding cutting needs.
• Star-shaped line: Featuring six or more cutting edges, star-shaped line is the most durable option for heavy-duty use. It slices through dense, woody vegetation with minimal effort and lasts far longer than round or square line in rough conditions, though it is also the most expensive option.
• Polymer-coated line: This line has a tough outer coating that resists abrasion from rocks, concrete, and dirt. It’s a great choice for users who frequently cut near hardscapes, as it lasts 2-3 times longer than standard uncoated line in these conditions.

In addition to shape, line diameter is a key specification. Most residential Troy-Bilt models use 0.065-inch diameter line, while heavy-duty commercial models use 0.080-inch diameter line for added strength. Never use a line thicker than the manufacturer’s recommended size, as this will overload the engine and can cause the head to overheat or break.

Signs You Need to Reline Your Troy-Bilt Weed Eater

It’s easy to wait until your line breaks completely to replace it, but catching wear early will save you time and frustration mid-job. Look for these common signs that it’s time to reline your Troy-Bilt weed eater:

• Frequent line breakage during normal use, even when cutting only soft grass
• Uneven cutting or torn, ragged grass instead of a clean, smooth trim
• Line does not advance when you tap the bump head on the ground, even after clearing jams
• Visible fraying, splitting, or excessive wear on the exposed section of line
• Repeated jams in the cutting head, even after clearing out grass and debris

If you notice any of these issues, a full reline will almost always restore your trimmer’s performance. In some cases, if the spool itself is cracked or the feed holes are clogged beyond cleaning, you may need to replace the entire spool assembly, but this is far less common than a simple line replacement.

Tools and Materials You’ll Need for Relining

One of the best parts of relining your Troy-Bilt weed eater is that it requires no specialized tools or expensive equipment. You likely already have everything you need in your garage or toolbox. Gather these items before you start to make the process as smooth as possible: (See Also:How To Spool A Kobalt Weed Eater 2)

• Replacement weed eater line: Confirm the correct diameter and shape for your model before purchasing, as outlined in the previous section.
• Work gloves: Sharp line edges can cause small cuts, and gloves will also protect your hands from grass, dirt, and sap when handling the spool.
• Safety glasses: Always wear eye protection when working with or testing your weed eater to avoid injury from flying debris.
• Flathead screwdriver or included hex key: Most Troy-Bilt bump heads use a simple release mechanism that requires a small flathead screwdriver, or the hex key that comes included with most new Troy-Bilt trimmers.
• Wire cutters: Used to trim the line to the correct length after winding, and to remove any frayed ends from old line before installing the new spool.
• Clean rag: For wiping away grass, dirt, and debris from the cutting head before installing the new spool.

No power tools are required for this task, so you can complete a reline anywhere, even in a yard without access to electricity.

Step-by-Step Guide: How to Reline a Troy Bilt Weed Eater?

These steps are specific to Troy-Bilt bump feed heads, the most common feed system for Troy-Bilt residential and commercial trimmers. If you have an autofeed head, the line installation process is similar, but the spool removal mechanism may vary slightly. Always refer to your owner’s manual for model-specific instructions if you’re unsure.

1. Disconnect the spark plug for safety: Locate the spark plug on the side of the trimmer’s engine. Grip the rubber boot firmly and pull it straight off the spark plug to disconnect it. This step is non-negotiable, as it prevents the trimmer from accidentally starting while you’re working on the head, eliminating the risk of serious lacerations.
2. Remove the bump head cap: Most Troy-Bilt bump heads have a round plastic cap that twists counterclockwise to release. Some newer models have small plastic release tabs on the side of the cap that you press inward while twisting to unlock it. Set the cap aside in a safe, visible spot so it doesn’t get lost during the process.
3. Extract the old line spool: Once the cap is removed, you’ll see the round plastic spool holding the old line. Grip the spool firmly and pull it straight out of the head housing. If it’s stuck due to debris or tangled line, gently wiggle it side to side to loosen it without forcing it, which could break the spool or head.
4. Clear debris from the head: Use your clean rag to wipe away all grass, dirt, and broken line fragments from the inside of the bump head housing. Check the small line feed holes on either side of the spool cavity to make sure they’re not clogged, as clogged holes will prevent new line from advancing properly even with a perfectly installed spool.
5. Wind the new line onto the spool: Take your replacement line and insert one end into one of the feed holes on the spool. Wind the line tightly around the spool in the direction indicated by the arrow printed on the top of the spool (this is almost always clockwise for Troy-Bilt bump heads). Wind 8 to 10 even turns of line, making sure it’s wound tightly without overlapping or gaps. Leave 6 to 8 inches of line sticking out of the feed hole when you’re finished. Important: Do not over-wind the spool, as excess line will bind inside the head and prevent proper advancement when you bump the trimmer.
6. Reinstall the spool in the head: Align the small tabs on the edge of the spool with the slots in the bump head housing, then push the spool firmly into place until you hear a click. Make sure the ends of the line are sticking out of both feed holes on either side of the head.
7. Reattach the bump head cap: Line up the tabs on the cap with the slots on the head housing, then twist the cap clockwise until it is snug. Do not over-tighten the cap, as this can strip the soft plastic threads on the head and make it impossible to remove the cap later.
8. Reconnect the spark plug and test the trimmer: Push the spark plug boot back onto the spark plug until you hear a click to ensure it’s fully seated. Start the trimmer and let it run for 10 to 15 seconds to warm up, then tap the bottom of the bump head firmly against a hard, smooth surface (like a concrete patio or a large, flat rock) while the trimmer is running at full throttle. The line should advance 2 to 3 inches with each tap. If it does not advance, double-check that the line is wound in the correct direction and the spool is fully seated in the head.

Troy-Bilt Bump Head vs. Autofeed Head: Key Differences

Troy-Bilt manufactures two main types of line feed systems for its weed eaters: the classic bump head and the newer autofeed head. Understanding the differences between these two systems will help you choose the right replacement parts and use your trimmer correctly. The table below breaks down the key distinctions:

If you have a bump head, the step-by-step relining guide above applies directly to your model. Autofeed heads use a similar spool installation process, but the cap removal mechanism may differ, so always check your owner’s manual for model-specific instructions. The line size and type requirements are identical for both feed systems, so you can use the same replacement line for either head type as long as it matches your model’s specifications.

Tips for Extending Your Weed Eater Line Life

Relining your trimmer is a simple fix, but there are steps you can take to make your line last longer between replacements, saving you time and money over time. Follow these best practices to get the most out of your cutting line:

• Always use the exact line diameter and shape recommended for your Troy-Bilt model to avoid excess strain on the engine and premature line wear.
• Avoid cutting against concrete, rocks, or other hard surfaces, as this grinds down the line much faster than cutting grass and weeds.
• Clean the bump head and spool after each use to remove grass, dirt, and sap that can cause the line to jam or wear out prematurely.
• Store your weed eater in a cool, dry place out of direct sunlight when not in use, as UV exposure can make line brittle and prone to breaking.
• Don’t overfill the spool with line, as excess line will rub against the inside of the head and wear down faster, plus it will cause tangles and feeding issues.
• If you frequently cut thick, woody vegetation, switch to a heavier-duty square or star-shaped line, which holds an edge longer than standard round line.

Common Mistakes to Avoid When Relining

Even a simple task like relining can lead to frustrating issues if you make a common error. Avoid these mistakes to ensure your reline goes smoothly and your trimmer performs at its best: (See Also:How To Start A Stihl Fs40c Weed Eater)

• Winding the line in the wrong direction: This is the most common cause of line not advancing when you bump the head. Always check the arrow printed on the spool before winding, and if you’ve already wound it backwards, simply rewind the line in the correct direction before reinstalling the spool.
• Using the wrong line size: A line that’s too thick will overload the engine and cause premature wear, while a line that’s too thin will break constantly and won’t cut effectively. Always verify the correct size in your owner’s manual before purchasing replacement line.
• Skipping the spark plug disconnect: This is a major safety hazard that can lead to serious lacerations if the trimmer starts accidentally while you’re working on the head. Always disconnect the spark plug first, every time you perform maintenance on the cutting head.
• Over-tightening the bump head cap: This can strip the plastic threads on the head, making it impossible to remove the cap later for future relines. Tighten the cap until it’s snug, but don’t use excessive force.
• Not clearing old debris from the head: Grass and dirt buildup in the head cavity will clog the line feed holes and cause jams, even with a brand new spool. Always wipe the head clean before installing a new spool to avoid this issue.
• Leaving too much or too little line exposed: If less than 2 inches of line is sticking out of the head, you won’t get an effective cut. If more than 6 inches is exposed, the line is more likely to tangle or break. Trim the line to 3 to 4 inches after installing the spool for optimal performance.

Frequently Asked Questions

How Often Should I Reline My Troy-Bilt Weed Eater?

The frequency of relining depends on how often you use your trimmer and the conditions you cut in. For light residential use (1 to 2 times per month, cutting only grass and soft weeds), you’ll typically need to reline every 2 to 3 months. For heavy use, such as commercial landscaping or cutting thick, woody vegetation weekly, you may need to reline every 4 to 6 weeks. It’s also best to reline as soon as you notice signs of wear, rather than waiting for the line to break completely mid-job.

What Size Line Does My Troy-Bilt Weed Eater Use?

Most residential Troy-Bilt weed eaters use 0.065-inch diameter round line, while heavy-duty models designed for thick vegetation use 0.080-inch diameter line. The easiest way to confirm the correct size is to check the label printed on your existing line spool, or refer to your owner’s manual. Using a line size that’s too large will put excess strain on the engine and can damage the head, while a line that’s too small will break frequently and provide poor cutting performance.

Why Is My Line Not Advancing When I Bump the Head?

If your line isn’t advancing when you tap the bump head, start by checking the most common causes first: First, confirm the line is wound in the correct clockwise direction (check the arrow on the spool). Second, make sure the spool is seated fully in the head housing; a partially installed spool will prevent the feed mechanism from working. Third, check that you haven’t overfilled the spool with line, as excess line will bind inside the head. If those checks don’t fix the issue, clear any debris from the line feed holes, or inspect the bump head for cracked or worn components that may need replacement.

Can I Use Third-Party Replacement Line for My Troy-Bilt Weed Eater?

Yes, you can use third-party replacement line as long as it matches the exact diameter and shape (round, square, etc.) specified for your model. Third-party line is often more affordable than official Troy-Bilt OEM line, and most high-quality third-party options perform just as well for residential and light commercial use. Just avoid cheap, low-quality line that breaks easily and wears out quickly, as it can cause more jams and require more frequent relining. (See Also:How To Replace Homelite Weed Eater Head)

Conclusion

Relining your Troy-Bilt weed eater is one of the simplest and most cost-effective maintenance tasks you can perform to keep your outdoor equipment in top shape. As this guide shows, learning how to reline a Troy Bilt weed eater requires no special skills, just a few basic tools and 10 to 15 minutes of your time. By following the step-by-step instructions for bump head relining, using the correct line for your model, avoiding common mistakes, and following our tips to extend line life, you can save money on repairs, avoid the frustration of a broken trimmer mid-job, and extend the overall lifespan of your Troy-Bilt equipment. Regular maintenance like relining, cleaning the cutting head, and inspecting for wear will keep your weed eater running smoothly for years, no matter if you’re maintaining a small residential yard or managing a large commercial property.